Harman Kardon AVR 354 Manuel d'utilisateur télécharger pdf (Page 35)

INITIAL SETUP

Before you begin enjoying your new receiver, a few adjustments should

be made to configure the AVR 354 to match your actual system.

Make sure that you have connected a video display to one of the

video

monitor outputs on the receiver. When you turn on your display and the

AVR, if the display is connected to the AVR via an analog video (com-

posite, S-video or component) connection, you may see a plain black

screen. If that happens, press the front-panel Resolution Button, and the

current video output resolution will appear in the Message Display. Use

the

⁄

Button to change it to 480i, which should be compatible with all

video displays, then press the OK Button to select the new setting. You

will be prompted to accept or cancel the change; the CANCEL message

will appear on the front panel. Press the

Button to view the ACCEPT

option, and then press the OK Button to complete the change to the out-

put resolution. The Main Menu should appear when you press the AVR

Settings Button on the remote, or the AVR Button on the front panel.

See Figure 47.

Figure 47 – Main Menu

Although it’s possible to configure the AVR using only the remote and

the front-panel messages, we recommend that you use the full-screen

menu system.

NOTE: When using the AVR’s on-screen menu system, we

recommend selecting a video output resolution of 720p or higher

for best legibility, and to provide graphics that simplify some

configuration options. Depending on the resolution selected, the

menus shown by your system may vary in appearance.

Using the On-Screen Menu System

The menu system is accessed by pressing the AVR Settings Button

on the remote. See Figure 48.

Figure 48 – Settings Buttons

The Main Menu will appear (see Figure 47), and if a video source is

playing, it will be visible behind the transparent menu.

The menu system consists of five main menus: Source Selection,

Setup Source, Speaker Setup, Zone 2 and System.

Use the

⁄

‹

›

Buttons on the remote or front panel to navigate

the menu system, and press the OK Button to select a menu or setting

line or to enter a new setting.

The current menu, setting line or setting will appear in the Message

Display as well as on screen.

To return to the previous menu or exit the menu system, press the

Back/Exit Button. Be certain all settings are correct, as any changes you

have made will be retained.

We recommend that most users follow the instructions in this INITIAL

SETUP section to configure a basic home theater system. You may

return to these menus at any time to make additional adjustments.

Thanks to the EzSet/EQ system, most of the menu adjustments may

be saved until you have become more familiar with the AVR, and are

therefore described in the Advanced Functions section.

The Initial Setup section requires that you complete all of the steps

in the Installation section that apply to your receiver. You should have

connected all of your loudspeakers and a video display, as well as your

source devices. You should be able to turn on the receiver and view

the main menu on

your video display when you press the AVR Settings

Button. If necessary, reread the Installation Section and the beginning of

this section before continuing.

Configure the AVR 354 Using EzSet/EQ Technology

One of the most important and perhaps often overlooked aspects of

setting up a home theater system is to calibrate the receiver to match

the loudspeakers, which enables the AVR to perform at its best.

Until recently, most receivers required the user to perform the calibration

and configuration manually, a somewhat tedious process that called for

a good ear or the purchase of an SPL (sound-pressure level) meter.

Although you may configure the AVR 354 manually, as described in

the Advanced Features section, we recommend that you take advantage

of our signature EzSet/EQ system.

Before beginning, eliminate extraneous background noise that might

affect the results, such as noisy air conditioning. Try to avoid making

any loud noises while running EzSet/EQ setup.

IMPORTANT SAFETY NOTE: During the EzSet/EQ procedure,

a series of very loud test tones will be played through all of the

speakers. Avoid sitting or standing close to any one speaker

during the procedure. If you are particularly sensitive to loud

noises, you may wish to leave the room and have someone

else run the EzSet/EQ process.

Step One – Place the included EzSet/EQ microphone in the listening

position, or in the center of the room, at about the same height as the

listeners’ ears. The microphone features a threaded insert on the bottom

so that it can be mounted on a camera tripod for stability.

Step Two – Plug the EzSet/EQ microphone into the Headphone

Jack/EzSet/EQ Microphone Input Jack on the front of the receiver.

See Figure 49.

AVR354-OM-HiRes.qxd 5/22/08 4:43 PM Page 35

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 75 76

Commentaires sur ces manuels

Pas de commentaire

Harman Kardon AVR 354 Manuel d'utilisateur Page 35

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Harman Kardon AVR 354